Technical data for ASTM A193 Grade B8 Class 2 and B8M Class 2 stainless bolting supplied by Benchmark: mechanical properties by diameter, heavy hex dimensions, typical tightening torque, nuts, threads and documentation. Use the button below to save or print it as a PDF.
Download / print this data sheet (PDF) or call 800-580-4195 and we will email a copy
ASTM A193 Grade B8 Class 2 is Type 304 stainless steel that is carbide solution treated and then strain hardened. The cold work raises its strength well above standard Class 1 stainless – up to 125 ksi tensile and 100 ksi yield at 3/4″ and under – while keeping the corrosion resistance of 304.
Benchmark supplies B8 and B8M Class 2 heavy hex bolts, studs and threaded rod across Canada, with matching nuts, mill test reports and grade stamping on every order.
| KEY DATA | |
|---|---|
| Standard | ASTM A193/A193M |
| Grades | B8 Class 2 (304), B8M Class 2 (316) |
| Condition | Carbide solution treated, strain hardened |
| Diameters | 1/4″ to 1-1/2″ (others on request) |
| Max. hardness | 35 HRC |
| Marking | Class 2 grade stamp (B8SH underlined) |
| Nominal diameter | B8 Cl. 2 tensile | B8 Cl. 2 yield | B8M Cl. 2 tensile | B8M Cl. 2 yield | Min. elongation | Max. hardness |
|---|---|---|---|---|---|---|
| Up to 3/4″ | 125 ksi | 100 ksi | 110 ksi | 95 ksi | 12% | 35 HRC |
| Over 3/4″ to 1″ | 115 ksi | 80 ksi | 100 ksi | 80 ksi | 15% | 35 HRC |
| Over 1″ to 1-1/4″ | 105 ksi | 65 ksi | 95 ksi | 65 ksi | 20% | 35 HRC |
| Over 1-1/4″ to 1-1/2″ | 100 ksi | 50 ksi | 90 ksi | 50 ksi | 28% | 35 HRC |
Elongation shown for B8 Class 2. Class 1 B8 / B8M: 75 ksi tensile, 30 ksi yield at all diameters. Always confirm requirements with the engineer of record.
| Diameter | UNC threads/in | 8UN threads/in | Width across flats | Head height |
|---|---|---|---|---|
| 1/2″ | 13 | — | 7/8″ | 5/16″ |
| 5/8″ | 11 | — | 1-1/16″ | 25/64″ |
| 3/4″ | 10 | — | 1-1/4″ | 15/32″ |
| 7/8″ | 9 | — | 1-7/16″ | 35/64″ |
| 1″ | 8 | 8 | 1-5/8″ | 39/64″ |
| 1-1/8″ | 7 | 8 | 1-13/16″ | 11/16″ |
| 1-1/4″ | 7 | 8 | 2″ | 25/32″ |
| 1-3/8″ | 6 | 8 | 2-3/16″ | 27/32″ |
| 1-1/2″ | 6 | 8 | 2-3/8″ | 15/16″ |
Standard thread length: 2 × diameter + 1/4″ for bolts up to 6″ long, 2 × diameter + 1/2″ over 6″. Fully threaded and custom thread lengths on request.
| Diameter | Dry (K = 0.20) | Lubricated (K = 0.15) | Anti-seize (K = 0.13) |
|---|---|---|---|
| 1/2″ | 59 ft·lb | 44 ft·lb | 38 ft·lb |
| 5/8″ | 118 ft·lb | 88 ft·lb | 77 ft·lb |
| 3/4″ | 209 ft·lb | 157 ft·lb | 136 ft·lb |
| 7/8″ | 269 ft·lb | 202 ft·lb | 175 ft·lb |
| 1″ | 404 ft·lb | 303 ft·lb | 262 ft·lb |
| 1-1/8″ | 465 ft·lb | 349 ft·lb | 302 ft·lb |
| 1-1/4″ | 656 ft·lb | 492 ft·lb | 427 ft·lb |
| 1-1/2″ | 878 ft·lb | 659 ft·lb | 571 ft·lb |
T = K × D × F, with F = 50% × minimum yield × tensile stress area. Estimates only; follow the joint designer’s or gasket manufacturer’s torque where given. Stainless threads gall when dry – a lubricant or anti-seize is recommended. For other preloads use the B8 Class 2 torque calculator.
Grade (B8 or B8M Class 2), product type, diameter, thread, length (and thread length if not standard), quantity, nuts and washers needed, delivery location and required date.
Notes: a) Confirm the product suits your application before ordering. b) Values are ASTM A193 minimums or nominal dimensions; certified values are on the mill test report supplied with each order. c) Data subject to change without notice. Document B8C2-DS Rev. 1, November 2026.
Benchmark supplies B8 and B8M Class 2 bolting for bridge bearings and anchor rods, structural steel, pressure piping and valves, water and wastewater treatment, and industrial maintenance. Send your bolt list or call 800-580-4195.