Canada flag
United States flag

A193 B8 Class 2 Bolt Data Sheet

A193 B8 Class 2 stainless steel bolts with nuts and washers

Bolts, Studs and Threaded Rod – Technical Data

Technical data for ASTM A193 Grade B8 Class 2 and B8M Class 2 stainless bolting supplied by Benchmark: mechanical properties by diameter, heavy hex dimensions, typical tightening torque, nuts, threads and documentation. Use the button below to save or print it as a PDF.

A193 B8 Class 2 technical data

Download / print this data sheet (PDF)   or call 800-580-4195 and we will email a copy

ASTM A193 Grade B8 Class 2 is Type 304 stainless steel that is carbide solution treated and then strain hardened. The cold work raises its strength well above standard Class 1 stainless – up to 125 ksi tensile and 100 ksi yield at 3/4″ and under – while keeping the corrosion resistance of 304.

Benchmark supplies B8 and B8M Class 2 heavy hex bolts, studs and threaded rod across Canada, with matching nuts, mill test reports and grade stamping on every order.

KEY DATA
StandardASTM A193/A193M
GradesB8 Class 2 (304), B8M Class 2 (316)
ConditionCarbide solution treated, strain hardened
Diameters1/4″ to 1-1/2″ (others on request)
Max. hardness35 HRC
MarkingClass 2 grade stamp (B8SH underlined)
14–21 day typical lead timevs the 6–8 weeks many suppliers quote

Products

  • Heavy hex bolts – heads to ASME B18.2.1, lengths and thread lengths to your list, fully threaded on request
  • Threaded rod – continuously threaded, cut to length
  • Stud bolts – fully threaded, double-end and tap-end studs, supplied with two heavy hex nuts
  • Nuts – ASTM A194 Grade 8 (B8) and 8M (B8M) heavy hex; strain-hardened (S1), jam and coupling nuts; all nut types
  • Threads – UNC, UNF, UNEF, 8UN, metric, left-hand; Class 2A or 3A
  • Washers – stainless flat washers to match

Typical applications

  • Bridge bearing assemblies, anchor plates and anchor rods
  • Stainless structural connections in corrosive or wash-down areas
  • Flanged piping, valves and pressure equipment
  • Bolting through structural thermal breaks (with STB-1 washers and bushings)

Documentation and quality

  • Mill test reports supplied with every order
  • Every bolt grade stamped; studs and rod stamped or end-marked for Class 2
  • Class 2 is not interchangeable with Class 1 (75 ksi tensile / 30 ksi yield) – substitutions need the engineer of record’s approval

Mechanical properties – ASTM A193 Class 2 minimums

Nominal diameterB8 Cl. 2 tensileB8 Cl. 2 yieldB8M Cl. 2 tensileB8M Cl. 2 yieldMin. elongationMax. hardness
Up to 3/4″125 ksi100 ksi110 ksi95 ksi12%35 HRC
Over 3/4″ to 1″115 ksi80 ksi100 ksi80 ksi15%35 HRC
Over 1″ to 1-1/4″105 ksi65 ksi95 ksi65 ksi20%35 HRC
Over 1-1/4″ to 1-1/2″100 ksi50 ksi90 ksi50 ksi28%35 HRC

Elongation shown for B8 Class 2. Class 1 B8 / B8M: 75 ksi tensile, 30 ksi yield at all diameters. Always confirm requirements with the engineer of record.

Heavy hex bolt dimensions (ASME B18.2.1, nominal)

DiameterUNC threads/in8UN threads/inWidth across flatsHead height
1/2″13—7/8″5/16″
5/8″11—1-1/16″25/64″
3/4″10—1-1/4″15/32″
7/8″9—1-7/16″35/64″
1″881-5/8″39/64″
1-1/8″781-13/16″11/16″
1-1/4″782″25/32″
1-3/8″682-3/16″27/32″
1-1/2″682-3/8″15/16″

Standard thread length: 2 × diameter + 1/4″ for bolts up to 6″ long, 2 × diameter + 1/2″ over 6″. Fully threaded and custom thread lengths on request.

Typical tightening torque – B8 Class 2, UNC, 50% of minimum yield

DiameterDry (K = 0.20)Lubricated (K = 0.15)Anti-seize (K = 0.13)
1/2″59 ft·lb44 ft·lb38 ft·lb
5/8″118 ft·lb88 ft·lb77 ft·lb
3/4″209 ft·lb157 ft·lb136 ft·lb
7/8″269 ft·lb202 ft·lb175 ft·lb
1″404 ft·lb303 ft·lb262 ft·lb
1-1/8″465 ft·lb349 ft·lb302 ft·lb
1-1/4″656 ft·lb492 ft·lb427 ft·lb
1-1/2″878 ft·lb659 ft·lb571 ft·lb

T = K × D × F, with F = 50% × minimum yield × tensile stress area. Estimates only; follow the joint designer’s or gasket manufacturer’s torque where given. Stainless threads gall when dry – a lubricant or anti-seize is recommended. For other preloads use the B8 Class 2 torque calculator.

What to send for a quote

Grade (B8 or B8M Class 2), product type, diameter, thread, length (and thread length if not standard), quantity, nuts and washers needed, delivery location and required date.

Notes: a) Confirm the product suits your application before ordering. b) Values are ASTM A193 minimums or nominal dimensions; certified values are on the mill test report supplied with each order. c) Data subject to change without notice. Document B8C2-DS Rev. 1, November 2026.

The Benchmark B8 Class 2 range

Mill test reports with every orderGrade stamped for Class 214–21 day lead timeAll nut and thread typesShips across Canada

Benchmark supplies B8 and B8M Class 2 bolting for bridge bearings and anchor rods, structural steel, pressure piping and valves, water and wastewater treatment, and industrial maintenance. Send your bolt list or call 800-580-4195.