Canada flag
United States flag

B8 vs B8 Class 2 vs B7 Bolts

A193 B8 Class 2 stainless steel bolts with nuts and washers

Which A193 Bolt Grade Do You Need?

ASTM A193 covers several bolting grades that look alike on a drawing but behave very differently in service. B7 is high-strength alloy steel, B8 Class 1 is standard 304 stainless, and B8 Class 2 is 304 stainless that has been strain hardened for strength close to B7 at smaller diameters. B8M is the 316 version. This guide compares strength, corrosion resistance, cost and availability so you can specify – or substitute – the right grade.

B8 vs B8 Class 2 vs B8M vs B7 at a glance

B7B8 Class 1B8 Class 2B8M Class 2
MaterialAlloy steel (4140 / 4142), quenched and tempered304 stainless, solution treated304 stainless, solution treated and strain hardened316 stainless, solution treated and strain hardened
Min. tensile125 ksi (to 2-1/2″)75 ksi125 ksi up to 3/4″, falling to 100 ksi at 1-1/2″110 ksi up to 3/4″, falling to 90 ksi at 1-1/2″
Min. yield105 ksi (to 2-1/2″)30 ksi100 ksi up to 3/4″, falling to 50 ksi at 1-1/2″95 ksi up to 3/4″, falling to 50 ksi at 1-1/2″
Corrosion resistanceLow – needs a coating (zinc, galvanizing or similar)GoodGoodBetter in chlorides, salt and de-icing exposure
MagneticYesEssentially noSlightly, from the cold workSlightly, from the cold work
Matching nutA194 2HA194 8A194 8 (S1 strain hardened if specified)A194 8M
Relative costLowestLowHigherHighest
AvailabilityWidely stockedWidely stockedLimited – often 6–8 weeks elsewhere; Benchmark 14–21 daysLimited – Benchmark 14–21 days

Strength values are ASTM A193 minimums. Always confirm requirements with the engineer of record.

How to choose

Choose B7 when

  • You need high strength at larger diameters and the joint is dry, painted or protected
  • Service is high-temperature piping or pressure equipment where the specification calls for B7
  • Corrosion is controlled by a coating rather than the bolt material

Choose B8 Class 1 when

  • Corrosion resistance matters but loads are light – 30 ksi yield is less than a third of B7

Choose B8 Class 2 when

  • You need stainless corrosion resistance and real structural strength, especially at 3/4″ and under
  • The drawings or a DOT bridge standard call for strain-hardened austenitic stainless – common for bridge bearing anchor rods and anchor plates
  • Bolts are exposed to weather, moisture or wash-down and coatings are not acceptable

Choose B8M Class 2 when

  • Exposure includes chlorides – marine air, road salt, de-icing chemicals, pools or chemical plants – where 316 resists pitting better than 304

Why Class 1 cannot replace Class 2

B8 Class 1 and Class 2 are the same 304 stainless, but Class 2 is cold worked after solution treatment. That strain hardening more than triples the yield strength at small diameters (100 ksi vs 30 ksi up to 3/4″). Swapping in Class 1 to beat a long lead time leaves the connection with a fraction of its design strength – so a substitution always needs the engineer of record’s written approval.

The benefit of strain hardening falls as diameter grows: at 1-3/8″ to 1-1/2″ Class 2 yield is 50 ksi. Check the strength table for your exact diameter, or use the B8 Class 2 torque calculator, which applies the correct strength for each size.

Class 2 bolts are identified by the grade marking with an underline (B8SH underlined) and are supplied with mill test reports confirming the Class 2 properties.

B8 vs B7 FAQ

Is B8 Class 2 as strong as B7?

Up to 3/4″, B8 Class 2 matches B7’s 125 ksi minimum tensile with 100 ksi yield (B7: 105 ksi). Above 3/4″ Class 2 strength drops with diameter, down to 100 ksi tensile and 50 ksi yield at 1-1/2″, while B7 stays at 125/105 ksi up to 2-1/2″.

Can I use B7 instead of stainless B8 Class 2?

Only if the engineer approves and corrosion is handled another way. B7 is alloy steel and rusts without a coating, so it is not a direct replacement in exposed or wet locations.

What is the difference between B8 and B8M?

B8 is Type 304 stainless; B8M is Type 316, which contains molybdenum for better resistance to chlorides. Strength is slightly lower for B8M Class 2 at small diameters (110 ksi vs 125 ksi tensile up to 3/4″).

Which nuts go with B8 Class 2 bolts?

ASTM A194 Grade 8 heavy hex nuts, or Grade 8M for B8M. Some specifications call for strain-hardened nuts (Supplement S1). Benchmark supplies all nut types.

How quickly can I get B8 Class 2?

Benchmark’s typical lead time is 14–21 days, compared with the 6–8 weeks many suppliers quote, with mill test reports and grade stamping on every order.

The Benchmark B8 Class 2 range

Mill test reports with every orderGrade stamped for Class 214–21 day lead timeAll nut and thread typesShips across Canada

Benchmark supplies B8 and B8M Class 2 bolting for bridge bearings and anchor rods, structural steel, pressure piping and valves, water and wastewater treatment, and industrial maintenance. Send your bolt list or call 800-580-4195.